Product Description
The Wind-Resistant Sign Post is a cantilever support built from a main vertical post and one or more horizontal arms that position traffic signs above or close to the driving lanes. The two common forms are the single-cantilever F-type, installed on one side of the road and extending in one direction, and the double-cantilever T-type, which extends toward both sides from the main post. An F-type structure serves exit advance information, lane guidance, ramp merging areas, and large directional panels placed over part of the roadway, while a T-type structure carries signs serving different directions or several lanes where the approved road layout needs a wider arrangement. These poles are chosen precisely where a normal roadside single post cannot provide the required sign position or viewing angle: highway exits, interchange sections, ramp merging areas, lane guidance locations, and large roadside directional panels. The steel components receive hot-dip galvanizing with reference to ISO 1461.
An overhead cantilever pole is a wind-load structure first and a sign holder second: the panel catches wind like a sail, and the arm, main post, flange, and foundation must resist that load together. Our technical team develops the structure around the approved sign panel area, wind load, installation height, flange construction, stiffening plates, and foundation design, rather than sizing the post only by the cantilever length, and the workshop checks the left-or-right cantilever direction, arm length, sign mounting holes, and transport section plan before any cutting starts. Because a wrong direction is only discovered when the arm fails to reach the correct lane, this drawing-based review is where fabrication experience pays off: fewer returned components and a pole matched to the site wind conditions.
Specifications
|
Parameter |
Specification |
|
Structural Forms |
Single-cantilever F-type or double-cantilever T-type |
|
Main Post Diameter |
Φ273, Φ325, Φ377, or Φ426 mm |
|
Main Post Wall Thickness |
6–12 mm |
|
Cantilever Length |
3–12 m |
|
Cantilever Arm Diameter |
Commonly Φ140–219 mm |
|
Total Structure Height |
Normally 6–9 m |
|
Surface Treatment |
Hot-dip galvanized with reference to ISO 1461 |
|
Order Basis |
Structural drawing and foundation drawing approved by the project design team |

Applications
1. Highway Exits and Exit Advance Signs - F-type arms place the exit information over the lanes at the decision point, where a roadside panel would be read too late.
2. Interchange Sections - T-type structures extend signs toward two sides from a single post, supporting multi-directional information where the road layout splits.
3. Ramp Merging Areas - Cantilever-mounted lane guidance panels keep merging drivers informed of the lane arrangement ahead.
4. Overhead Large Directional Panels - Where the roadside space is narrow or the viewing angle demands an overhead position, the structure is sized against the panel area and project wind load.
Customization
The main post, cantilever arms, flanges, connecting plates, and stiffening components are manufactured to F-type or T-type structural drawings. Cantilever direction, arm length, sign mounting holes, flange dimensions, and the sectional transport plan are configured per project. Hot-dip galvanizing follows the ISO 1461 reference. Product marking and packaging can carry the buyer brand; OEM and ODM orders are accepted, and customized structures enter batch production after first-piece or key structural connection confirmation.
Packaging & Transportation
Because long horizontal components are difficult to ship assembled, the structure is commonly divided into sections for transport, with on-site connection through flanges or another project-specified method. Main posts and cantilever arms are bundled separately, flange surfaces and component ends receive additional protection, and bolts, connecting plates, and smaller accessories are packed in separate boxes. Each set is marked by installation point, timber reinforcement is added inside the container, and production photos and videos are provided during production. EXW is our preferred trade term; for FOB or CIF shipments, ocean freight risk transfers to the buyer after the goods board the vessel.
FAQ
Q1: What documents are needed before manufacturing a cantilever sign pole?
A1: We need the structural drawing and the foundation drawing, or the documents approved by the project design team. The review covers the cantilever direction, arm length, sign mounting holes, flange dimensions, and transport section plan, so the structure matches its installation point.
Q2: How is a wrong cantilever direction avoided?
A2: The left-or-right direction is checked during drawing review, and the first piece or key structural connection is confirmed before batch production. Each set is then marked by installation point, which prevents reversed components on site.
Q3: When can inspection be arranged during production?
A3: Buyers may arrange inspection after welding, before or after galvanizing, or before container loading. Independent inspection can cover the material, dimensions, welding, and coating, and production and inspection records are managed by order.
Hot Tags: wind-resistant sign post, China wind-resistant sign post manufacturers, suppliers, factory, Cantilever Sign Pole, heavy duty traffic sign post, road sign pole, road sign steel post, steel road sign pole, traffic sign mounting column

